Standards
- ASTM D7094ASTM D6450
- IP620
- SH/T 0768
Correlation to
- ASTM D56
- ASTM D3828
- DIN 51758
- ISO 2719
- ISO 3679
- ISO 3680
- ISO 13736
- IP34
- IP170
- JIS K2265
Autosampler for Flash Point Testing
ERAFLASH S10 is the first 10-position autosampler for flash point testing. It uses the inherently safe methods ASTM D7094, ASTM D6450, and IP620. With a low sample volume of only 1-2 ml and the continuously closed sample cups, they are ideally suited to build a completely safe autosampler for flash point testing. ERAFLASH S10 is the perfect solution for high-throughput laboratories and takes up very little laboratory space.
This makes ERAFLASH S10 the ideal analyzer for unattended flash point testing.
Cost-efficient Fast Flash Point Testing
When looking at valuable products, especially with small batch sizes, flash point testing using the well-known Pensky Martens principle can consume a significant amount of sample, thus leading to high analytical costs. When performing flash point testing according to ASTM D7094 and IP620 just 2 ml of the sample are needed. ASTM D6450 reduces this volume even further to 1 ml.
ERAFLASH S10 is therefore a welcome addition to testing labs handling large amounts of costly samples every day. This includes fragrances, paints, and varnishes producers.
Peltier Boost Technology®
Similar to eralytics’ single position flash point tester the patented PBT – Peltier Boost Technology® allows flash point testing below 0 °C (32 °F) and above 200 °C (392 °F) with a single instrument. PBT separates the Peltier elements during the heat up at 100 °C shielding them from higher temperatures that would normally harm them. During the cool down, however, they can be used for active cooling starting at 200 °C and thus reduce the turnaround time significantly. PBT also facilitates the same temperature range of -25 °C (-13 °F) to 420 °C (788 °F) of our single position flash point tester in an autosampler for flash point testing.
A Cooling Lid for Shorter Turnaround Times
ERAFLASH S10’s optional cooling lid is an unsurpassed benefit, especially in applications that involve highly volatile samples. The lid keeps the pending samples at a stable temperature, which makes volatile compounds far less likely to evaporate before their measurement starts. Therefore, results are more precise and more reliable. With pre-cooled sample cups cooling during the measurement can be less intense, which results in shorter turnaround times.
Measurement Procedure
Just four easy steps are required for an unattended safe and fast flash point testing at maximum precision:
- Enter sample IDs and operator name
- Select the measurement standards and add additional parameters (e.g. expected flash point)
- Fill up to 10 sample cups with samples, place the sample cups on the carousel and close the cover plate
- Press the RUN button
During flash point testing the instrument visualizes the measurement procedure on the screen showing the sample and oven temperature as well as pressure gauge displaying the pressure increase after ignition. Additional information about the currently measured sample, as well as finished and still samples to be measured are displayed. After the measurements the flash point temperature is corrected for the atmospheric pressure and rounded to the next 0.5°C. All results will be saved in the corresponding result file.
ERAFLASH S10 Feature Video
- High throughput with the 10-position autosampler
- Inherently safe with no open flame
- Only a very low sample volume of 1-2 mL needed
- Takes up very little laboratory bench space
- Fully compliant with ASTM D6450, ASTM D7094, and IP620
- Measurement of fuels, lubricants, fragrances, flavors, paints, …
By loading the video, you agree to YouTube’s privacy policy.
Learn more
ERAFLASH S10 Operation Video
Watch this video to get an overview on the standard operation of ERAFLASH S10: From installation to measurement and some extended measuring options.
By loading the video, you agree to YouTube’s privacy policy.
Learn more
Autosampler for Flash Point Testing
ERAFLASH S10 is the first 10-position autosampler for flash point testing. It uses the inherently safe methods ASTM D7094, ASTM D6450, and IP620. With a low sample volume of only 1-2 ml and the continuously closed sample cups, they are ideally suited to build a completely safe autosampler for flash point testing. ERAFLASH S10 is the perfect solution for high-throughput laboratories and takes up very little laboratory space.
This makes ERAFLASH S10 the ideal analyzer for unattended flash point testing.
Autosampler for Flash Point Testing
ERAFLASH S10 is the first 10-position autosampler for flash point testing. It uses the inherently safe methods ASTM D7094, ASTM D6450, and IP620. With a low sample volume of only 1-2 ml and the continuously closed sample cups, they are ideally suited to build a completely safe autosampler for flash point testing. ERAFLASH S10 is the perfect solution for high-throughput laboratories and takes up very little laboratory space.
This makes ERAFLASH S10 the ideal analyzer for unattended flash point testing.
Cost-efficient Fast Flash Point Testing
When looking at valuable products, especially with small batch sizes, flash point testing using the well-known Pensky Martens principle can consume a significant amount of sample, thus leading to high analytical costs. When performing flash point testing according to ASTM D7094 and IP620 just 2 ml of the sample are needed. ASTM D6450 reduces this volume even further to 1 ml.
ERAFLASH S10 is therefore a welcome addition to testing labs handling large amounts of costly samples every day. This includes fragrances, paints, and varnishes producers.
Cost-efficient Fast Flash Point Testing
When looking at valuable products, especially with small batch sizes, flash point testing using the well-known Pensky Martens principle can consume a significant amount of sample, thus leading to high analytical costs. When performing flash point testing according to ASTM D7094 and IP620 just 2 ml of the sample are needed. ASTM D6450 reduces this volume even further to 1 ml.
ERAFLASH S10 is therefore a welcome addition to testing labs handling large amounts of costly samples every day. This includes fragrances, paints, and varnishes producers.
Peltier Boost Technology®
Similar to eralytics’ single position flash point tester the patented PBT – Peltier Boost Technology® allows flash point testing below 0 °C (32 °F) and above 200 °C (392 °F) with a single instrument. PBT separates the Peltier elements during the heat up at 100 °C shielding them from higher temperatures that would normally harm them. During the cool down, however, they can be used for active cooling starting at 200 °C and thus reduce the turnaround time significantly. PBT also facilitates the same temperature range of -25 °C (-13 °F) to 420 °C (788 °F) of our single position flash point tester in an autosampler for flash point testing.
Peltier Boost Technology®
Similar to eralytics’ single position flash point tester the patented PBT – Peltier Boost Technology® allows flash point testing below 0 °C (32 °F) and above 200 °C (392 °F) with a single instrument. PBT separates the Peltier elements during the heat up at 100 °C shielding them from higher temperatures that would normally harm them. During the cool down, however, they can be used for active cooling starting at 200 °C and thus reduce the turnaround time significantly. PBT also facilitates the same temperature range of -25 °C (-13 °F) to 420 °C (788 °F) of our single position flash point tester in an autosampler for flash point testing.
A Cooling Lid for Shorter Turnaround Times
ERAFLASH S10’s optional cooling lid is an unsurpassed benefit, especially in applications that involve highly volatile samples. The lid keeps the pending samples at a stable temperature, which makes volatile compounds far less likely to evaporate before their measurement starts. Therefore, results are more precise and more reliable. With pre-cooled sample cups cooling during the measurement can be less intense, which results in shorter turnaround times.
A Cooling Lid for Shorter Turnaround Times
ERAFLASH S10’s optional cooling lid is an unsurpassed benefit, especially in applications that involve highly volatile samples. The lid keeps the pending samples at a stable temperature, which makes volatile compounds far less likely to evaporate before their measurement starts. Therefore, results are more precise and more reliable. With pre-cooled sample cups cooling during the measurement can be less intense, which results in shorter turnaround times.
Measurement Procedure
Just four easy steps are required for an unattended safe and fast flash point testing at maximum precision:
- Enter sample IDs and operator name
- Select the measurement standards and add additional parameters (e.g. expected flash point)
- Fill up to 10 sample cups with samples, place the sample cups on the carousel and close the cover plate
- Press the RUN button
During flash point testing the instrument visualizes the measurement procedure on the screen showing the sample and oven temperature as well as pressure gauge displaying the pressure increase after ignition. Additional information about the currently measured sample, as well as finished and still samples to be measured are displayed. After the measurements the flash point temperature is corrected for the atmospheric pressure and rounded to the next 0.5°C. All results will be saved in the corresponding result file.
Measurement Procedure
Just four easy steps are required for an unattended safe and fast flash point testing at maximum precision:
- Enter sample IDs and operator name
- Select the measurement standards and add additional parameters (e.g. expected flash point)
- Fill up to 10 sample cups with samples, place the sample cups on the carousel and close the cover plate
- Press the RUN button
During flash point testing the instrument visualizes the measurement procedure on the screen showing the sample and oven temperature as well as pressure gauge displaying the pressure increase after ignition. Additional information about the currently measured sample, as well as finished and still samples to be measured are displayed. After the measurements the flash point temperature is corrected for the atmospheric pressure and rounded to the next 0.5°C. All results will be saved in the corresponding result file.
ERAFLASH S10 Feature Video
- High throughput with the 10-position autosampler
- Inherently safe with no open flame
- Only a very low sample volume of 1-2 mL needed
- Takes up very little laboratory bench space
- Fully compliant with ASTM D6450, ASTM D7094, and IP620
- Measurement of fuels, lubricants, fragrances, flavors, paints, …
By loading the video, you agree to YouTube’s privacy policy.
Learn more
ERAFLASH S10 Feature Video
- High throughput with the 10-position autosampler
- Inherently safe with no open flame
- Only a very low sample volume of 1-2 mL needed
- Takes up very little laboratory bench space
- Fully compliant with ASTM D6450, ASTM D7094, and IP620
- Measurement of fuels, lubricants, fragrances, flavors, paints, …
By loading the video, you agree to YouTube’s privacy policy.
Learn more
ERAFLASH S10 Operation Video
Watch this video to get an overview on the standard operation of ERAFLASH S10: From installation to measurement and some extended measuring options.
By loading the video, you agree to YouTube’s privacy policy.
Learn more
ERAFLASH S10 Operation Video
Watch this video to get an overview on the standard operation of ERAFLASH S10: From installation to measurement and some extended measuring options.
By loading the video, you agree to YouTube’s privacy policy.
Learn more
